Asbestos Gaskets

We are one of the leading manufacturers of Asbestos Gaskets.

Gaskets are cut from gasket sheet material that typically consists of rubber and a strong, heat-resistant material such as asbestos. Sheets of compressed asbestos were used until the 1980s in gasket material and heat seals, as the long and hollow asbestos fibers provided superior and low-cost strength and resistance to high temperatures when the fibers were compressed.

Newer gasket material that does not contain asbestos may be made with various rubbers, carbon fibers and fillers such as paper, copper, silicone, graphite, metal, cork, felt, neoprene or fiberglass.

Gasket material and heat seals made from asbestos are used in almost every mechanical system that involved the transport of gases, hot oils, steam, chemicals, grease or acid. Uses for gaskets and heat seals include:

ASBESTOS GASKET - MATERIAL SPITMAAN STYLE 20 STEAM:

Use                                                      :           General Purpose Application.

Recommended Maximum Temperature :            380 deg.C.

Recommended Maximum Pressure   :           35 kg / sq.cm.

Specification Compliance                   :           I.S 2712-1998 GRADE W/3 , I.S 2712 – 1971 GRADE C

ASBESTOS GASKET - MATERIAL SPITMAAN STYLE 51 HIGH PRESSURE:

Use                                                      :           Against Steam, Neutral – dyes, alkalies, oils, fats, non flammable

                                                                        gases.

Recommended Maximum Temperature :           440 deg.C.

Recommended Maximum Pressure :           80 kg / sq.cm.

Specification Compliance                   :           I.S 2712-1998 GRADE, I.S 2712 – 1979  GRADE W/2        

ASBESTOS GASKET - MATERIAL SPITMAAN STYLE 54 SUPER:

Use                                                      :           Against  Saturated Steam, Oxygen, Petroleum distillates, Oils,

 Fats, fuels, hydrocarbons, alcholes, solvents etc.

Recommended Maximum Temperature :           550 deg.C.

Recommended Maximum Pressure   :           150 kg / sq.cm.

Specification Compliance                   :           I.S 2712-1998 GRADE, I.S 2712 – 1979  GRADE W/1

 ASBESTOS GASKET - MATERIAL SPITMAAN STYLE 20 METALLIC:

Use                                                      :         General Purpose Application where temperature & pressure are not  too severe.

Recommended Maximum Temperature :           415 deg.C.

Recommended Maximum Pressure  :           40 kg / sq.cm.

ASBESTOS GASKET - MATERIAL SPITMAAN STYLE 51 METALLIC:

Use                                                      :           Industrial Application & General Engineering Service.                   

Recommended Maximum Temperature :           480 deg.C.

Recommended Maximum Pressure   :           100 kg / sq.cm.

ASBESTOS GASKET - MATERIAL SPITMAAN STYLE 54 SUPER METALLIC:

Use                                                    :           Used where high pressure & temperature are to be resisted. Cylinder

                                                                        Head gaskets, combustion engines, air compressor.

Recommended Maximum Temperature  :            600 deg.C.

Recommended Maximum Pressure   :           160 kg / sq.cm.

Specification Compliance                   :           I.S 2712 – 1979  GRADE W/1, I.S 2712 – 1971  GRADE A/S

ASBESTOS GASKET - MATERIAL SPITMAAN STYLE 39:

Use                                                      :           Against dry & wet steam, water, gases, oils, alkalies, chemical fuels.

Recommended Maximum Temperature :             440 deg.C.

Recommended Maximum Pressure   :           80 kg / sq.cm.

Specification Compliance                   :           I.S 2712 – 1979  GRADE O/2, I.S 2712 – 1979  GRADE W/2

ASBESTOS GASKET - MATERIAL SPITMAAN STYLE 59 OIL:

Use                                                    :           In Petrochemicals Industries, Oil & Petroleum Industries. Recommended Maximum Temperature          :           550 deg.C.

Recommended Maximum Pressure   :           150 kg / sq.cm.

Specification Compliance                   :           I.S 2712 – 1979  GRADE O/1, I.S 2712 – 1971  GRADE A/O

ASBESTOS GASKET - MATERIAL SPITMAAN STYLE 60 ACID:

Use                                                    :           In Organic, Inorganic, mineral acids, nitric acids,

Recommended Maximum Temperature :           210 deg.C.

Recommended Maximum Pressure   :           150 kg / sq.cm.

Specification Compliance                   :           I.S 2712 – 1979  GRADE A/1,  I.S 2712 – 1998